Jivelite is a cut down Squeezebox control application derived from Logitech’s Squeezebox Jive.
Originally developed and released by Adrian Smith. Currently maintained by Ralph Irving. piCorePlayer fully supports Jivelite on the Raspberry Pi’s Official 7" Touch Display.
InstallationJivelite can be installed on piCorePlayer via the [Tweaks] page on the piCorePlayer web interface.
Jivelite [Settings] > [piCorePlayer] screen
More information Announce: JiveLite - cut down squeezebox control application - Triode Jivelite for piCorePlayer - Ralph Irving Latest Jivelite - Ralph Irving - github Jivelite for piCorePlayer - Ralph Irving - github
1.5 inch st7789 spi LCD display, 240×240, with piCorePlayer. Info This display comes with the pins unsoldered. You have to solder them yourself.
This display is perfect, if you want to build a small device-like player or net radio showing the title or broadcast information. Together with a RPi Zero W and a HiFiBerry MiniAMP or small mono DAC/amp Audio Amp SHIM (pic below), you get a complete solution. What we need Raspberry Pi 3, 4, or Zero WH 8GB Micro SD card Cheap 1.
2.2 inch ili9341 spi LCD display, 320×240, with piCorePlayer. Info It’s a little bit tricky get those displays running under piCorePlayer. Other spi displays like Waveshare or Spotpear, that are fitted with the same ili9341 chip, may work too with this overlay. I tested it with Spotpear 2.4 inch spi LCD.
This display is perfect, if you want to build a small device like player or net radio showing the title or broadcast information.
Waveshare 4 inch resistive display, spi Touch, 480×800, HDMI, with piCorePlayer. Step 1 - Connect the display to your Raspberry PI Plug the display directly on the GPIO pins of your RPi and connect the HDMI plug with an HDMI-adaptor. If you need additional pins for other purpose, wire the pins 1, 2, 6, 19, 21, 22, 23, 26) and connect the HDMI-Plug with a HDMI Cable.
Pin Symbol Discription 1 3,3 V Power positive (3.
Waveshare 5 inch HDMI Display, 800x480, resistive spi touch with piCorePlayer. What we need Raspberry Pi 2, 3, 4 or piZero WH 8GB Micro SD card Waveshare 5 inch display, resistive spi-touch with HDMI-adaptor Optional: Some jumper wires, female to female Powersupply, 5V, >= 2,5 A PC or Laptop, Putty installed Preparation Plug the display directly on the GPIO pins of your PI and connect the HDMI plug with an HDMI-adaptor If you need additional pins for other purpose, wire the pins 1, 2, 6, 19, 21, 22, 23, 26) and connect the HDMI plug with a HDMI cable.
I nice write-up by The Fan Club - How to setup piCorePlayer Jivelite for use with a Waveshare 5.5 inch AMOLED touchscreen. More information Waveshare 5.5 inch Touch AMOLED Display Download piCorePlayer Burn piCorePlayer onto a SD card Determine your piCorePlayer IP address Access piCorePlayer via ssh Edit config.txt piCorePlayer aliases piCorePlayer CLI Basic vi commands Raspberry Pi config.cfg Waveshare 4.1 TFT + piCorePlayer + Jivelite Documentation / fb / fbcon.
Waveshare 7.9inch Capacitive Touch LCD Display, 400×1280, HDMI, IPS, Toughened Glass Cover with piCorePlayer. Step 1 - Prepare SD card Put a fresh pCP image on to the SD card—see Burn piCorePlayer onto a SD card. While the SD card is still in the laptop/pc: Enter wifi credentials in wpa_supplicant.conf.sample and “save as” wpa_supplicant.conf. Add the following lines to config.txt, in the Custom Configuration area at the end of the file (between the Begin-Custom and End-Custom lines).
Add an IR receiver and setup a JustBoom IR remote. Today nearly every device is fitted with an IR remote, so why not a piCorePlayer? If your display has no touch or you do not want to control your device by a smartphone, an IR remote is very helpful. What we need Raspberry Pi piCorePlayer 8 with Jivelite installed A running display connected to RPi An TSOP4838 or similar IR receiver like OS-0038N 3 jumper wires, female to bare wire Soldering iron, solder, some heat shrink tube A JustBoom IR remote Info TSOP4838 IR receivers are sold in differing designs!
Create keytables for IR remote. Today nearly every device is fitted with an IR remote, so why not piCorePlayer? If your display has no touch capability or you do not want to control your device by a smartphone, an IR remote can be very helpful. Since 4.19 linux kernel the original LIRC uinput drivers have been removed. We need to configure IR keytables to get IR remotes running with pCP.
Your display has no touch function and you want to control jivelite by hardware? Here is the solution.
How to control Jivelite by rotary encoders and pushbuttons.
Thanks to chill for the sbpd-script.sh script (pirate-audio amp).
You can simply control jivelite by adding rotary encoders and/or pushbuttons to the GPIO’s of your Raspberry Pi. What we need A running piCorePlayer with Jivelite installed and a display connected to your Raspberry Pi Some pushbuttons (normally open) One or two rotary encoders (for this purpose, do not use encoders with power supply!
The Software and Information is provided "as is" without warranty of any kind, either express or implied, including without limitation any implied warranties of condition, uninterrupted use, merchantability, fitness for a particular purpose, or non-infringement.
Raspberry Pi is a trademark of the Raspberry Pi Foundation.